Raspberry PI Overclock Config

Hello All,


Welcome back! A few people have asked me for help with overclocking their RaspPi, so I decided to let others in on what I have done to get a successful 1.3ghz overclock. 

** Warning ** 
This overclock will void your warranty


The strong shall continue and below will behold the loot :)

|:---------------------|------------------------------------------------------:|
|      Option          |                                                       |
|:---------------------|------------------------------------------------------:|
| arm_freq             | frequency of ARM in MHz. Default 700.         
| gpu_freq             | Sets core_freq, h264_freq, isp_freq, v3d_freq
|                      | together.
| core_freq            | frequency of GPU processor core in MHz. Default 250.
| h264_freq            | frequency of hardware video block in MHz. Default 250.
| isp_freq             | frequency of image sensor pipeline block in MHz.
|                      | Default is 250.
| v3d_freq             | frequency of 3D block in MHz. Default 250.
| sdram_freq           | frequency of SDRAM in MHz. Default 400.
| over_voltage         | ARM/GPU core voltage adjust. [-16,8] equates to
|                      | [0.8V,1.4V] with 0.025V steps. Default 0 (1.2V) [1]
| over_voltage_sdram   | Sets over_voltage_sdram_c, over_voltage_sdram_i,
                       | over_voltage_sdram_p together
| over_voltage_sdram_c | SDRAM controller voltage adjust. [-16,8] equates to
|                      | [0.8V,1.4V] with 0.025V steps. Default 0 (1.2V) [1]
| over_voltage_sdram_i | SDRAM I/O voltage adjust. [-16,8] equates to
|                      | [0.8V,1.4V] with 0.025V steps. Default 0 (1.2V)[1]
| over_voltage_sdram_p | SDRAM phy voltage adjust. [-16,8] equates to
|                      | [0.8V,1.4V] with 0.025V steps. Default 0 (1.2V)[1]

|:----------------------------------------------------------------------------:|

----backup 07/15/2017 11:30pm

# For more options and information see

# http://rpf.io/configtxtreadme

# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode

#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible and your display can output without overscan

#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console

 goes off screen, and negative if there is too much border

#overscan_left=16

#overscan_right=16

#overscan_top=16

#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus

overscan.

#framebuffer_width=1280

#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output

#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)

#hdmi_group=1

#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in

# DMT (computer monitor) modes

#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or no display

#config_hdmi_boost=4

# uncomment for composite PAL

#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.

arm_freq=1300

over_voltage=5

gpu_freq=500

# sdram

overclock

sdram_freq=500

sdram_schmoo=0x02000020

over_voltage_sdram_p=6

over_voltage_sdram_i=4

over_voltage_sdram_c=4

# Uncomment some or all of these to enable the optional hardware interfaces

#dtparam=i2c_arm=on

#dtparam=i2s=on

#dtparam=spi=on

# Uncomment this to enable the lirc-rpi module

dt

overlay=lirc-rpi

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)

dtparam=audio=on